blob: d85cfe18780dd035fffa7fbdbee14607f8a9717d (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
|
#include <xc.h>
#include "t6963c_specific.h"
#include "t6963c/t6963c.h"
// CONFIG1
#pragma config WPCFG = WPCFGDIS // Write Protect Configuration Page Select->Last page (at the top of program memory) and Flash Configuration Words are not write-protected
#pragma config WPDIS = WPDIS // Segment Write Protection Disable->Segmented code protection is disabled
#pragma config WPFP = WPFP255 // Write Protection Flash Page Segment Boundary->Highest Page (same as page 170)
#pragma config SOSCSEL = EC // Secondary Oscillator Power Mode Select->External clock (SCLKI) or Digital I/O mode(
#pragma config ALTPMP = ALPMPDIS // Alternate PMP Pin Mapping->EPMP pins are in default location mode
#pragma config WPEND = WPENDMEM // Segment Write Protection End Page Select->Protected code segment upper boundary is at the last page of program memory; the lower boundary is the code page specified by WPFP
#pragma config WUTSEL = LEG // Voltage Regulator Wake-up Time Select->Default regulator start-up time is used
// CONFIG2
#pragma config POSCMOD = NONE // Primary Oscillator Select->Primary oscillator is disabled
#pragma config FCKSM = CSDCMD // Clock Switching and Fail-Safe Clock Monitor->Clock switching and Fail-Safe Clock Monitor are disabled
#pragma config OSCIOFNC = ON // OSCO Pin Configuration->OSCO/CLKO/RC15 functions as port I/O (RC15)
#pragma config PLL96MHZ = ON // 96MHz PLL Startup Select->96 MHz PLL is enabled automatically on start-up
#pragma config PLLDIV = NODIV // 96 MHz PLL Prescaler Select->Oscillator input is used directly (4 MHz input)
#pragma config IOL1WAY = ON // IOLOCK One-Way Set Enable->The IOLOCK bit (OSCCON<6>) can be set once, provided the unlock sequence has been completed. Once set, the Peripheral Pin Select registers cannot be written to a second time.
#pragma config FNOSC = FRCPLL // Initial Oscillator Select->Fast RC Oscillator with Postscaler and PLL module (FRCPLL)
#pragma config IESO = ON // Internal External Switchover->IESO mode (Two-Speed Start-up) is enabled
// CONFIG1
#pragma config WDTPS = PS32768 // Watchdog Timer Postscaler->1:32,768
#pragma config GCP = OFF // General Segment Code Protect->Code protection is disabled
#pragma config FWDTEN = OFF // Watchdog Timer->Watchdog Timer is disabled
#pragma config ICS = PGx1 // Emulator Pin Placement Select bits->Emulator functions are shared with PGEC1/PGED1
#pragma config WINDIS = OFF // Windowed WDT->Standard Watchdog Timer enabled,(Windowed-mode is disabled)
#pragma config JTAGEN = OFF // JTAG Port Enable->JTAG port is disabled
#pragma config FWPSA = PR128 // WDT Prescaler->Prescaler ratio of 1:128
#pragma config GWRP = OFF // General Segment Write Protect->Writes to program memory are allowed
void init(void) {
// CPDIV 1:1; RCDIV FRC/2; DOZE 1:8; G1CLKSEL disabled; DOZEN disabled; ROI disabled;
CLKDIV = 0x3100;
// GCLKDIV 1;
CLKDIV2 = 0x0000;
t6963c_init();
}
int main(void) {
TRISBbits.TRISB0 = 0;
while (1) {
delay_ns(1000);
LATBbits.LATB0 = 0;
delay_ns(100);
LATBbits.LATB0 = 1;
}
return 0;
}
|
